GST, IEC and Udyam registered exporter · Mumbai, India+91 77388 20834 · exports@greenmarkexports.in
Tool

Cocopeat hydration volume calculator

Quick answer

Enter the number of 5 kg blocks or 650 g bricks to see the approximate litres of growing medium and the water needed to hydrate them. Figures are typical, so test with your own batch.

By Greenmark Exports, Mumbai · Updated 2026-11-18

  • hydration calculator

How it works

The tool uses typical expansion of 70 to 75 L per 5 kg block and 8 to 9 L per 650 g brick.

Limits

Actual expansion depends on fibre share and compression.

Estimate litres and water

Typical figures: 5 kg block makes about 70 to 75 litres with 20 to 25 litres of water; a 650 g brick makes about 8 to 9 litres.

Key takeaways

  • The tool uses typical expansion of 70 to 75 L per 5 kg block and 8 to 9 L per 650 g brick.
  • Actual expansion depends on fibre share and compression.

Treat results as planning figures and confirm exact numbers on the proforma invoice.

What the calculator does

The hydration calculator estimates how much water a cocopeat block or brick needs and how many litres of loose medium it makes. It helps growers plan tubs and trays and helps retailers check a litre claim. The figures are typical; test a sample from your lot.

Inputs and assumptions

Enter the product and the number of units. The calculator uses typical expansion volumes, such as about 70 to 75 litres for a 5 kg block and about 8 to 9 litres for a 650 g brick, and typical water use of about 20 to 25 litres for a block. Real figures vary with the pith and the press.

How to use the result

Prepare the tub size, the water and the drainage. Add water in stages and rake the block. Use the output to plan how many trays or bags you can fill.

A worked example

If you hydrate ten 5 kg blocks, you need roughly 200 to 250 litres of water and you obtain about 700 to 750 litres of medium. If your own test shows 65 litres per block, use that number in the plan.

Limits

The calculator is an estimate. Water quality, soak time and block density all affect the result.

Planning trays, bags and tubs

Convert the litre estimate into units you use. A standard seed tray, a 10-litre pot or a 30-litre bag each needs a known volume. Divide the total litres by the unit volume to plan how many you can fill from the blocks you hydrate. Keep a reserve for settling, because hydrated coir packs down after watering.

Why your own test beats a calculator

Run a test with one block from your lot. Measure the water, the soak time and the loose volume. Replace the typical numbers in your plan with your own, and repeat the test when you change lots.

Quick checklist before you hydrate

Clean tub, clean water, a rake, gloves, a place to drain and a plan for the finished volume. Hydrate only what you can use within a few days.

Worked example for a nursery

A nursery plans to fill 2,000 trays of 10 litres each. That needs 20,000 litres of medium. At about 70 litres per 5 kg block, that is roughly 286 blocks, so the nursery rounds up to 300 to allow for settling and waste. At roughly 20 to 25 litres of water per block, the nursery needs between about 6,000 and 7,500 litres of water for hydration. The figures are typical, so a test block comes first.

Common planning errors

Using a volume figure from a different brand, forgetting that hydrated coir settles after watering, hydrating more than you can use in a few days, and ignoring the water quality. Test one block and update the calculator inputs with your own result.

Buyer checklist

  • Treat the result as a planning figure.
  • Confirm exact numbers on the proforma invoice.
  • Re-run the calculator with your real pack and pallet data.

Short answers written to be read aloud by a voice assistant or a smart speaker.

How much water does a 5 kg cocopeat block need?

About 20 to 25 litres of water, and it expands to roughly 70 to 75 litres of loose medium. Confirm with a test.

People also ask

Is the result exact?

No. Test a block from your lot.

Can I use hot water?

Warm water is fine. Avoid very hot water.

People also search for

  • cocopeat hydration calculator
  • how much water for coco block
  • coco peat expansion
  • coir volume calculator
  • hydration calculator

Explore more on Greenmark Exports

About this page

Who wrote and checked it

Written by the Greenmark Exports export desk in Mumbai. Greenmark Exports is a partnership firm established 20 December 2025, with partners Fahad Jamal, Vikrant Kale. The firm holds GST registration (27ABDFG9926H1Z2), an Importer-Exporter Code (ABDFG9926H) and Udyam registration (UDYAM-MH-18-0511530).

How we prepared it

We build every page from public standards and agency guidance, which we list under Sources, and from the trade documents we work with ourselves. Where a figure is typical, not guaranteed, the page says so. We have not run grow trials ourselves and do not present first-hand crop results.

Last reviewed

2026-11-18. Found something out of date? Email exports@greenmarkexports.in and we will check it and correct the page.

Sources used

Need a specification or a quote? Send your requirement or message us on WhatsApp.

Questions and answers

How much water per block?

About 20 to 25 litres for a 5 kg block.

How much medium per brick?

About 8 to 9 litres.

Ready to source from India?

Tell us the product, quantity and destination port. We reply with a specification sheet and a quotation.

Request a quoteWhatsApp